Mirror, Outside Flag-Mount
IF THE IMAGE IS TOO SMALL, click it.
F7TZ17682DAA Right chrome manual
F7TZ17683DAB Left chrome manual
F1TZ17682C Right black manual
F1TZ17682D Left black manual
F7TZ17682BAA Right chrome power
F5TZ17683BA Left chrome power
F5TZ17682E Right black power
F5TZ17683E Left black power
Mirror Glass Removal:
1. Push in on the inboard edge of the glass assembly until it stops.
2. Protect mirror body with a rag or similar material at the outboard edge and insert a flat blade screwdriver (in about one inch) between the mirror body and glass assembly.
3. **THIS DOESN'T WORK** Pry the glass assembly out from mirror body until it snaps loose. **THE GLASS INVARIABLY SNAPS BEFORE THE TABS RELEASE**
4. Remove screwdriver and continue to pull the glass assembly by hand until it is completely unsnapped.
5. ('96 Bronco only) Scribe the wire colors into the plastic for reassembly later, then disconnect the two circuits (turn signal and ground) from the terminals on the back of the glass assembly.
Mirror Front Trim Removal:
1. Remove the 4 T-10 screws from the outer corners behind the mirror glass.
2. Lift the trim away from the mirror head.
Mirror Motor Removal:
1. Mark the motor with tape/grease pencil/scribe to indicate top of motor.
2. Remove the four screws attaching the motor to the mirror body.
3. Pull motor away from the mirror body.
4. Remove the plastic cover plate from the back of the motor. Pull off by hand.
5. Use masking tape on the wires. Mark on the wire its location in the motor with the terminal number shown on the motor where the wires plug in, and scribe the wire colors into the plastic.
6. Carefully pull the wires/terminals out of the motor.
Mirror Assembly Removal:
1. Remove front door trim panel (23942).
2. On power mirrors, disconnect outside mirror control wiring (14A684) at inner door skin below speaker.
3. Remove two black countersunk T-25 screws attaching outside rear view mirror (17682) to the exterior of the front door (20124).
4. Remove one 8mm screw attaching outside rear view mirror to the interior of the front door.
5. Remove outside rear view mirror.
Mirror Head Removal:
1. Remove T-10 screw from mirror base gasket, and slide gasket off base brace arm & wiring (if equipped).
2. Remove two T-20 screws from base and lift mirror head away from base, feeding power mirror wiring (if equipped) through pivot rivet.
Mirror Head Installation: Follow removal procedures in reverse order.
Mirror Motor Installation:
1. Install wires into the motor by matching the terminal number marked on the wires and on the motor. Remove masking tape from the wires.
2. Make sure wires are placed in the retaining slots in back of motor, then align the opening in the plastic cover plate with the wires on the back of motor and push on back cover.
3. Make sure the rubber seal is properly installed on the motor.
4. Position motor in mirror body using the mark (added during removal) indicating top of motor and line up the four screw holes.
5. Install the four screws and hand-tighten. Do not overtighten.
Mirror Front Trim Installation: Follow removal procedures in reverse order.
Mirror Glass Installation:
1. ('96 Bronco only) Connect signal and ground wires to mirror glass. Verify signal display operation by operating the right and left turn signals.
2. Position glass assembly in mirror, making sure the U-shaped alignment tabs on the glass assembly are lined up with the motor actuator bar, and move glass around slightly until it drops into place.
3. Push on center of the glass assembly to snap it into place.
4. Check glass assembly for looseness. If loose, push on glass assembly until it is fully seated.
Mirror Assembly Installation: Follow removal procedures in reverse order.
Mirror Control Removal:
1. Insert a small, thin-bladed screwdriver into spring tab slots located at front and rear of window regulator switch housing (14527) and apply pressure to make the window regulator switch housing pop out.
2. Remove three screws attaching connectors to window regulator switch housing.
3. Remove outside rear view mirror control (17B676) by carefully prying the outside rear view mirror control from connector using a small screwdriver, then prying mirror control from window regulator switch housing.
Mirror Control Installation: Follow removal procedure in reverse order. The outside rear view mirror control is keyed to the connector and can be installed only one way.
See also:
.
