21SwayBarTab2WD.JPG
2727 hits | 96.9 KB | Posted: 3/30/11
The frame tab on a 2WD 1/2-ton frame faces the wrong direction for my towing eye brackets to be properly supported. But a 2WD probably doesn't need towing eyes anyway.

Curiously, my brackets DO fit the 2WD heavy frame (without crumple-zone convolut...
(Posted in: '92-96 Towing Eyes)

TowEyesAlPaint.JPG
1130 hits | 54.31 KB | Posted: 4/30/13
SOLD Ford Aluminum Towing Eyes (casting#: F85A17A554BA) painted Valspar Implement gloss black

I sometimes find these junkyarding, restore & sell them in addition to the brackets I make. They can be found in lightweight Aluminum or heavy cast steel, ...
(Posted in: '92-96 Towing Eyes)

BallJointXtorch.jpg
303 hits | 81.05 KB | Posted: 8/29/22
Ball Joint Removal with a torch
IF THE IMAGE IS TOO SMALL, click it.

Ball joint presses are cumbersome, weak, and very slow, requiring a lot of physical effort especially if the ball joint doesn't come out. This is actually easier both on the mechan...
(Posted in: Front Diff & Ball Joints)

FuelPressureGauge.JPG
27458 hits | 73.98 KB | Posted: 9/18/10
Fuel Pressure Gauge
A Sears/Craftsman gauge costs $35-55, but many parts stores will loan/rent tools like this for a deposit. To check pressure while driving, the gauge should be positioned so it's visible, but the driver should not WATCH the gauge. ...
(Posted in: '90-96 Fuel Pump System)

TransAutoControls96.JPG
15139 hits | 83.8 KB | Posted: 1/3/10
'96 Electronic Auto Trans Controls
IF THE IMAGE IS TOO SMALL, click it.
4R70W OSS: 450 to 750 Ohms

See also:

http://e...
(Posted in: Diagrams)

IAC Cutaway.jpg
27753 hits | 81.72 KB | Posted: 8/4/05
IAC solenoid valves
Key off, IAC solenoid disconnected, resistance through the IAC pins should be between 6.0 and 13.0 ohms. Resistance from either pin to the case should be greater than 10Kohms.
NOTE: Due to diode in solenoid, place DVOM(plus) lead...
(Posted in: Diagrams)

TSB98-5A-35E-brakeCable.jpg
7004 hits | 40.2 KB | Posted: 4/18/09
TSB 98-5A-35 Rear Parking Brake Cables Bind - Vehicles Built Before 8/20/96, except chassis cab
Publication Date: MARCH 18, 1998

LIGHT TRUCK: 1992-97 F-250, F-350

ISSUE: The rear parking brake cables may bind and not allow the rear brake shoes ...
(Posted in: TSBs & FSAs (Recalls) for '83-96 Broncos & F150s)

CoolantFlowV8.jpg
69 hits | 70.64 KB | Posted: 5/19/24
Coolant flow for smallblock V-8s. The arrow exiting the top comes from the thermostat & goes to the radiator. The arrow entering the bottom comes from the radiator & goes into the water pump. The small channel shown from the top going forward & down ...
(Posted in: Diagrams)

EvapClean96F150.jpg
41 hits | 108.7 KB | Posted: 5/26/24
Evaporator Cleaning
IF THE IMAGE IS TOO SMALL, click it.

This truck was bought used with working A/C, but it didn't blow very hard. After a few months, it got bad enough to diagnose. The first step is to simply remove the 2 screws for the resisto...
(Posted in: General Purpose Pics)

DLC96BroncoC201.jpg
18989 hits | 35.24 KB | Posted: 2/1/05
OBD-II test connector (Motorcraft WPT615) located under glove box for '96 Bronco with EEC-V processor.

P0102 indicates the MAF signal went below 0.39V.
P0103 indicates the MAF Signal went above 3.90...
(Posted in: Diagrams)

TowEyesCmpr.jpg
4 hits | 119.48 KB | Posted: 5/28/24
'97-up Front Tow Hooks
IF THE IMAGE IS TOO SMALL, click it.

Ford used the same shape & mounting pattern for most 1/2-ton & lighter 4WD vehicles for about 2 decades, but the material & construction varied slightly. Some of these were also offered ...
(Posted in: '92-96 Towing Eyes)

BJlower.JPG
1136 hits | 139.36 KB | Posted: 10/24/14
Pressing the lower BJ (MotorCraft MCS-10253) in last, so it wasn't in the way of pressing the upper in (MotorCraft MCS-10339).

Removal was done with a ...
(Posted in: Front Diff & Ball Joints)

BJupper.JPG
1239 hits | 119.59 KB | Posted: 10/24/14
Pressing the upper BJ (MotorCraft MCS-10339) in first using the big Snap-On press & cups only took a minute.

Removal was done with a BPH & pipe scrap.

[url=https://www.supermotors.net/registry/media/...
(Posted in: Front Diff & Ball Joints)

BJout.JPG
1238 hits | 134 KB | Posted: 10/24/14
Removing these BJs was much faster than the previous set. The lower BJ (top in the photo) came out with one whack. The upper (using the pipe drift) took about 6.

[url=http://www.supermotors.net/registry/media/764867][img]http://www.supermotors.net...
(Posted in: Build)