a1.jpg
602 hits | 38.33 KB | Posted: 9/14/06
Mark the relative position of the driveshaft to the axel for later reinstall

b1.jpg
631 hits | 39.35 KB | Posted: 9/14/06
do the same for the dual u-joint end of the drive shaft.

c1.jpg
672 hits | 45.1 KB | Posted: 9/14/06
unfasten the ubolts and detach the driveshaft from the rear axel.

d1.jpg
621 hits | 39.42 KB | Posted: 9/14/06
unfasten the bolts and detach the driveshaft dual u-jount assembly from the transfercase. (note: t...

e1.jpg
553 hits | 52.46 KB | Posted: 9/14/06
here is the driveshaft as it came out of my bko

f1.jpg
604 hits | 43.37 KB | Posted: 9/14/06
I had taped up the rubber sleeve, wire brushed and sandblasted the driveshaft with the old ujoints s...

g1.jpg
532 hits | 53.8 KB | Posted: 9/14/06
here is the driveshaft after sand blasting and before I Primed and painted it chrome.

I1.jpg
671 hits | 53.76 KB | Posted: 9/14/06
here is the driveshaft all disassembled with the new parts ready to be put in. The part numbers f...

k1.jpg
579 hits | 53.41 KB | Posted: 9/14/06
a closer look at the dual u-joint chasis exploded view.

k2.jpg
508 hits | 47.94 KB | Posted: 9/14/06
The end mounting bracket has a swivel pressed into it and the hole in the swivel is where the spring...

i2.jpg
501 hits | 65.26 KB | Posted: 9/14/06
here is the set up I had used to disasemble and reassemble the driveshaft components. I used an arb...

l1.jpg
520 hits | 54.48 KB | Posted: 9/14/06
installing the ujoints are all pretty much the same process. get one axis of u joint in the drive ...

m1.jpg
555 hits | 54.69 KB | Posted: 9/14/06
press in the opposite cap.

n1.jpg
529 hits | 37.82 KB | Posted: 9/14/06
each u-joint endcap should be deep enough to allow the clip to be inserted into the groove like this...

o1.jpg
554 hits | 53.88 KB | Posted: 9/14/06
This is the inboard u-joint on the dual u-joint assembly. I had to remove the endcaps to insert the...

p1.jpg
504 hits | 45.77 KB | Posted: 9/14/06
taking the two endcaps I had removed I positioned the at opposite ends of the u-joint and pressed th...

q1.jpg
503 hits | 41.24 KB | Posted: 9/14/06
When setting up to attach the middle component to the dual u-joint assemble I had to line up the pre...

r1.jpg
562 hits | 59.51 KB | Posted: 9/14/06
This is the cup were the spring is that connects to the outboard u-joint bracket. I had filled the ...

s1.jpg
462 hits | 57.6 KB | Posted: 9/14/06
I had placed the mounting bracket in place making sure the spring was in place. I dont have the pi...

t1.jpg
561 hits | 82.51 KB | Posted: 9/14/06
here is the driveshaft with new paint and u-joints (x3)

u1.jpg
548 hits | 46.31 KB | Posted: 9/14/06
on install make sure that the alignment marks are lined up and your good to go.

v1.jpg
538 hits | 37.76 KB | Posted: 9/14/06