1.JPG
617 hits | 75.39 KB | Posted: 11/5/07
My rig has suffered HWB (Hot Weather Bug) since I got her. My TFI-PIP assembly just doesn't like hot...

2.JPG
525 hits | 62.35 KB | Posted: 11/5/07

3.JPG
520 hits | 65.28 KB | Posted: 11/5/07
All the electronic is covered by a sticky stuff, very difficult to remove. After trying to remove th...

4.JPG
535 hits | 45.75 KB | Posted: 11/5/07
After removing the back plate, I carefully removed the electronic circuit and the sticky stuff in or...

5.JPG
547 hits | 46.48 KB | Posted: 11/5/07
Drilled a hole for the wires

6.JPG
529 hits | 50.28 KB | Posted: 11/5/07

7.JPG
535 hits | 77.93 KB | Posted: 11/5/07
After soldering cables, some hot glue

8.JPG
461 hits | 43.52 KB | Posted: 11/5/07
For the other end of the harness I wanted a real plug to fit the module. Couldn't find one so I buil...

9.JPG
501 hits | 67.26 KB | Posted: 11/5/07
I removed the small step in the front

10.JPG
527 hits | 81.4 KB | Posted: 11/5/07
I used braided cable for the harness and welded female spade connectors

11.JPG
519 hits | 63.44 KB | Posted: 11/5/07
After that, placed the plug and used my glue gun to bond/protect/isolate the connectors

12.JPG
522 hits | 58.49 KB | Posted: 11/5/07
Filled all the plug wit hot glue and closed it

13.JPG
520 hits | 45.72 KB | Posted: 11/5/07

14.JPG
497 hits | 79.41 KB | Posted: 11/5/07
Final fit

15.JPG
506 hits | 80.79 KB | Posted: 11/5/07
Some non-adhesive tape and the harness was almost ready. Later I soldered ground connections.

16.JPG
550 hits | 46.65 KB | Posted: 11/5/07
I got a heat sink from a '94. After sand blasting I removed 7 fins and partially another 2

17.JPG
510 hits | 36.92 KB | Posted: 11/5/07
I did it that way so the fins will keep the connector in place avoiding disconnection

18.JPG
488 hits | 71.88 KB | Posted: 11/5/07
I was going to locate the module in the driver side fender, but decided to make the harness shorter ...

19.JPG
471 hits | 65.4 KB | Posted: 11/5/07
I have some concerns about this location because in case my A/C belt goes the module is very close, ...

20.JPG
489 hits | 77.76 KB | Posted: 11/5/07
Heat sink in place

21.JPG
499 hits | 52.08 KB | Posted: 11/10/07
Removed the module from the distributor and connected the dummy module harness. Picture is not good ...

23.JPG
461 hits | 83.8 KB | Posted: 11/10/07
At this point I discovered that my harness has a problem. Cables come from the dummy module connecto...

22.gif
604 hits | 247.21 KB | Posted: 11/10/07

24.JPG
482 hits | 44.01 KB | Posted: 11/10/07
Some grease in the heat sink

25.JPG
514 hits | 46.48 KB | Posted: 11/10/07
Plug the module to the connector before placing the module in the heat sink (otherwise you will not ...

26.JPG
478 hits | 83.05 KB | Posted: 11/10/07
Connect the module (don't need to extend the cables !!!), check timing and be sure everything is in ...