1965 Ford Mustang
| Owner: |
chero65 (All of this user's registries on SuperMotors) |
| From: |
Okinawa, Japan (Other registries outside the U.S) |
| Year, Make, & Model: |
1965 Ford Mustang (Other Ford Mustangs) |
| Avatar: |
 |
| Nickname: |
Stang |
| Mileage: |
|
| Engine: |
1974 302 out of anTorino (.030 bore), Holley Street Avenger 570, Comp Cam XTreme Energy 262 H camshaft (lifters, springs, retainers, roller rockers, timing chain, 3/8 nuts, TFS 170/58cc Twisted Wedge Heads, Comp Cams 7.300" hardened push rods, Edelbrock Performer Intake Non-EGR, POR15 gloss black engine enamel, ARP head/intake bolts, Edelbrock Victor Aluminum water pump, new OE timing chain cover, Proform black wrinkle valve covers/air cleaner/breather/bolt set, 1" phenolic carb spacer, ford racing dual sump 5 qt oil pan, melling oil pump, carter hi-po fuel pump, 160 degree thermostat, new OE thermostat housing, modified Heidts mm-130 weld in motor stands, Scott Drake Monte Carlo Bar/Straight/Flat Black, prothane polyurethane engine mounts, 3G 1 wire small body alternator, 90's 302 PMGR starter, Procomp billet cdi distributor, PC6AL ignition box, MSD blaster 2 coil/mount, Flowmaster 2.25" American Thunder exhaust kit, Champion 2 row radiator/shroud/2500 CFM fan, Ford Racing 9MM Red spark plug wires, ARP 1 3/4" header studs/nuts, Canton Road Race T oil pan and pick up, BBK ceramic coated shorty headers |
| Drivetrain: |
Currie Super 8" rear housing with Currie 28 spline axles/bearings/plates (stock width), Ford Racing M7003Z T5 transmission/bellhousing, ford racing billet flywheel (157 tooth/28.2 oz), Valeo 10.5" king cobra clutch, Mustang Steve clutch cable kit w/ bearings, Mustang Steve cross member, Modern Driveline offset shifter, Hurst stick, MBM Mustang II front suspension w/ Heidts coil overs 400# (welder series upper mount/coil over mount), TCI triangulated 4-link rear suspension w/ coil overs, rear disc brakes with Eldorado calipers/parking brake, MBM manual rack and pinion, prothane polyurethane trans mount, 1967 3rd member w/ 3.54 Richmond posi gears, SN95 Master Cylinder (PAA-0380 & PAA-B312 Metric bubble flare to SAE brake lines), SSBC Proportioning Valve/ebay bottom mount bracket, Lokar hand brake kit, MB Motoring Old School Gun Metal 17x8 wheels w/ 4.5 inch backspace and 235/45-17 Hankook Ventus V12 Evo Tires, Grab-A-Trak 1" front sway bar |
| Notes: |
Dynacorn Inner Fenders w/ Heidts inner fender panels, dynacorn radiator support, new fuel tank/sender/lines, new floor pans LH/RH, new rear quarters, 1975 Ford F150 manual tilt steering column, RH/LH/trunk rear brace/inner trunk bumper brackets, front frame boxed, sub frame connectors, dynacorn rear frame rails LH/RH, new front/rear valance, dynacorn 1 pc seat platform, Spectre front torque boxes, 18 gauge trunk divider, dynacorn firewall, dynacorn tail light panel, new Spectre rear floor extensions, Spectre outer wheelhouse extensions (both sides), front/rear bumper mounting kit, Scott Drake trunk filler panels, Dynacorn front fenders, Splatter Paint in trunk (gray/white), drip rails removed, new rear valance, Dynacorn PS/DS door, new upper/lower hinges, new trunk hinges, hood hinge spring delete with prop rod, 4 gauge alt/starter/battery/engine ground wires, side post quick disconnects, welded in rear valance, smoothed rear bumper, Grant 3 spoke Walnut steering wheel, all new tinted glass, dynacorn quarter window regulators, full weatherstrip kit, black TMI headliner, DII front and rear window trim, American Autowire harness 510125 w/ new heater motor and 2 spd wiper harness, MP products instrument panel/gauges, AAC black carpet 80/20, Corbeau Black Cloth Sport Seats, TMI black vinyl deck lid panel, TMI black std door panels, Speedway Motors steering column brace |
| Last Updated: |
4/18/2015 |
| Hits: |
8043 |
| Folder |
 |
 |
 |
Hits |
 |
Created |
Updated |
 pics | 906 | 0 | 3 | 213,628 | 0 | 6/22/12 | 4/18/15 |
Maintenance & Modification Logs
This user hasn't added any log entries, yet.
|
|
