framestart.jpg
242 hits | 62.86 KB | Posted: 7/6/14
Big things have small beginnings.
(Posted in: The Build)

framestart2.jpg
241 hits | 60.61 KB | Posted: 7/6/14
And now for the ribs.
(Posted in: The Build)

swingarm.jpg
256 hits | 37.44 KB | Posted: 7/6/14
Black it out...
(Posted in: The Build)

wheel.jpg
234 hits | 54.01 KB | Posted: 7/6/14
Shiny!
(Posted in: The Build)

leftsideframe.jpg
243 hits | 70.21 KB | Posted: 7/7/14
I added an extra half inch tube to the top of the cage to fill in the gap a little more. It snugs the frame up to the tank for a better looking fit. This pic also give a good idea of the fuel cock recess and access.
(Posted in: The Build)

Rightsideframe.jpg
236 hits | 70.92 KB | Posted: 7/7/14
The right side is the same as the left without the fuel access.
(Posted in: The Build)

tankon.jpg
233 hits | 70.53 KB | Posted: 7/7/14
With the tank on for the final fit. I cut the rear as well and ran all tubes so they flow the same lines forming a double V or chevrons, if you will, for the lower portion of the frame.
(Posted in: The Build)

tail.jpg
259 hits | 57.32 KB | Posted: 7/14/14
Add the rod to shape the tail.
(Posted in: The Build)

tail2.jpg
241 hits | 57.71 KB | Posted: 7/14/14
I will cut and shape the lower tail frame so it smooths out better, then sheet metal it in and begin paint prep. Almost done.
(Posted in: The Build)

Tail3.jpg
241 hits | 63.54 KB | Posted: 7/15/14
Sheet metal for the tail.
(Posted in: The Build)

tail4.jpg
257 hits | 59.39 KB | Posted: 7/15/14
From the rear.
(Posted in: The Build)

tail5.jpg
278 hits | 47.95 KB | Posted: 7/15/14
Sheet metal tacked in from the side. Still have some shaping and paint prep.
(Posted in: The Build)

CompletFrameFab.jpg
285 hits | 54.55 KB | Posted: 7/18/14
Metal work is done. A good washing before paint prep.
(Posted in: The Build)

CompletFrameFab2.jpg
254 hits | 65.22 KB | Posted: 7/18/14
The tail fits the seat very well. After a little filler to smooth out the sharp edges, it will flow nicely.
(Posted in: The Build)

CompletFrameFab3.jpg
203 hits | 62.05 KB | Posted: 7/18/14
Getting the rear to curve was a little tricky, but the end result was where it needed to be to maintain the lines of the bike. A little filler to smooth it out and it will be great. Going all metal also means that any damage can be repaired pretty ea...
(Posted in: The Build)

Rebar.jpg
223 hits | 66.35 KB | Posted: 7/18/14
Did not have the right size round bar laying around, but I did have some rebar that was just right! soaked it in rust inhibiter and BAM! The Fuel cock access is born!
(Posted in: The Build)

994134_10202191130684449_5082732725043633457_n.jpg
224 hits | 41.93 KB | Posted: 7/20/14
Working the filler is a long process and the sanding is labor intensive. But it is looking as planned and when the paint goes on, the lines will flow very nicely.
(Posted in: The Build)

IMG_0185.JPG
221 hits | 64.53 KB | Posted: 8/29/14
Finally got paint and clear on the frame after all the body work and endless sanding. Happy with the results and shape of the bike.
(Posted in: The Build)

IMG_0192.JPG
238 hits | 64.4 KB | Posted: 8/29/14
Stripped the tank bare and put a fresh three coats of BLVD Black on, followed by three coats of clear. A little wet sanding with 2000 and a quick polish in a few days and it will be solid.
(Posted in: The Build)

IMG_0193.JPG
268 hits | 82.19 KB | Posted: 8/29/14
Added two extra coats of clear to the wheels. They look a lot better.
(Posted in: The Build)

dryfitting1.jpg
264 hits | 63.72 KB | Posted: 10/11/14
Lining up the forks.
(Posted in: The Build)

dryfitting2.jpg
250 hits | 69.97 KB | Posted: 10/11/14
Ready for rubber.
(Posted in: The Build)

dryfitting3.jpg
303 hits | 65.52 KB | Posted: 10/11/14
Rubber and brakes are on the bike.
(Posted in: The Build)

dryfitting4.jpg
283 hits | 61.79 KB | Posted: 10/11/14
Superbike bars are on and I really like the look.
(Posted in: The Build)

dryfitting5.jpg
314 hits | 56.07 KB | Posted: 10/11/14
Getting closer.
(Posted in: The Build)

dryfitting6.jpg
318 hits | 57.5 KB | Posted: 10/11/14
The gold hand controls are amazing in contrast to the black skin.
(Posted in: The Build)

tailLEDs.jpg
323 hits | 49.79 KB | Posted: 10/11/14
Simple tail section.
(Posted in: The Build)

vapordash.jpg
308 hits | 79.95 KB | Posted: 10/11/14
Simple dash to match to the tail.
(Posted in: The Build)

brakes.jpg
295 hits | 76.18 KB | Posted: 10/17/14
I relocated the rear brake reservoir to be under the front seat bracket.
(Posted in: The Build)

Buttoned1.jpg
309 hits | 62.01 KB | Posted: 10/17/14
Just need to install the shorty exhaust.
(Posted in: The Build)

buttoned2.jpg
344 hits | 69.37 KB | Posted: 10/17/14
Pleased with the look.
(Posted in: The Build)

20150710_175650.jpg
903 hits | 74.02 KB | Posted: 8/1/15
2005 C50 Boulevard Custom Bobber
(Posted in: C50 Bobber)

20150710_175750.jpg
371 hits | 80.83 KB | Posted: 8/1/15
Offset 1929 Ford taillight; bullet turn indicators.
(Posted in: C50 Bobber)

20150710_175801.jpg
351 hits | 70.96 KB | Posted: 8/1/15
Custom Diamond plate hand made leather spring seat.
(Posted in: C50 Bobber)

20150710_175811.jpg
373 hits | 71.1 KB | Posted: 8/1/15
Black powder coated drag bar, 5 inch risers, Avon grips, and slim custom mirrors.

(Posted in: C50 Bobber)

20150710_175825.jpg
411 hits | 80.16 KB | Posted: 8/1/15
I removed the upper and lower fork covers; bullet front turn indicators.
(Posted in: C50 Bobber)

20150710_175839.jpg
335 hits | 75.28 KB | Posted: 8/1/15
Cobra Drag Exhaust
(Posted in: C50 Bobber)

20150526_210008.jpg
387 hits | 54.34 KB | Posted: 8/1/15
Side view
(Posted in: C50 Bobber)

20150526_210017.jpg
346 hits | 56.55 KB | Posted: 8/1/15
Aluminum Rear fender (little dusty); bullet rear indicator light.
(Posted in: C50 Bobber)

20150606_182809.jpg
332 hits | 53.45 KB | Posted: 8/1/15
This is what the fork covers look like...kinda bulky. Removed for a cleaner look.
(Posted in: C50 Bobber)

20150419_180414-1.jpg
463 hits | 61.27 KB | Posted: 8/1/15
Offset 1929 Taillight.
(Posted in: C50 Bobber)

20160713_180819.jpg
249 hits | 73.91 KB | Posted: 7/14/16
(Posted in: DR350 #3 Pink Shock)

20160713_180825.jpg
170 hits | 86.76 KB | Posted: 7/14/16
(Posted in: DR350 #3 Pink Shock)

20160713_180838.jpg
221 hits | 90.24 KB | Posted: 7/14/16
(Posted in: DR350 #3 Pink Shock)

20160713_180845.jpg
131 hits | 74.95 KB | Posted: 7/14/16
(Posted in: DR350 #3 Pink Shock)