1995 Ford Bronco
| Owner: |
dato1200 (All of this user's registries on SuperMotors) |
| From: |
Philly, PA, U.S.A. (Other registries in PA) |
| Year, Make, & Model: |
1995 Ford Bronco (Other Ford Broncos) |
| Avatar: |
 |
| Nickname: |
|
| Mileage: |
167000 |
| Engine: |
stock 5.0L |
| Drivetrain: |
M50D, TTB front and 8.8 rear all stock with 3.55 gears |
| Notes: |
Bought it in Janurary 07 from a Used Car dealer. Replaced the ball joints. Put in a bigger MSD coil, new plugs gapped a big bigger and new leads. Going to advance the timing by a couple of degrees soon.
Sitting at home, waiting to be installed:
35" Maxxis Bighorns
Superflex 5.5" inch lift
2" Body lift
Sky Shackle flip
Water temp and Oil Pressure Gauges |
| Last Updated: |
12/10/2008 |
| Hits: |
3666 |
windscreen2.JPG
609 hits | 70.6 KB | Posted: 12/10/08
Hit rock at 70+ mph. Little glass shards went all the way back to the parcel shelf under the rear window
windscreen1.JPG
584 hits | 84.94 KB | Posted: 12/10/08
Rock flicked up by car in front. 70+ mph
IMGA0013.JPG
604 hits | 33.39 KB | Posted: 1/3/08
IMGA0012.JPG
674 hits | 34.77 KB | Posted: 1/3/08
IMGA0011.JPG
549 hits | 35.87 KB | Posted: 1/3/08
The two bolts at the very top of the pic, are where the bracket is supposed to be mounted.
IMGA0010.JPG
571 hits | 25.66 KB | Posted: 1/3/08
IMGA0009.JPG
573 hits | 30.03 KB | Posted: 1/3/08
IMGA0008.JPG
604 hits | 32.94 KB | Posted: 1/3/08
IMGA0007.JPG
579 hits | 28.37 KB | Posted: 1/3/08
Bad night time shot.
The bracket is not big enough. A bolt cannot go through the holes in the bracket, and the axle pivot bushing.
IMGA0003a.JPG
691 hits | 48.05 KB | Posted: 1/3/08
The red line represents the axle housing.
The axle hits the back of the Superlift bracket. The holes drilled in the bracket will not line up with the hole through the axle pivot bushing.
IMGA0012.JPG
674 hits | 34.77 KB | Posted: 1/3/08
IMGA0003.JPG
652 hits | 49.81 KB | Posted: 1/3/08
Shot of the back end of the two brackets.
Note that the original bracket has a much bigger opening for the axle housing (highlighted better on next pic).
IMGA0002.JPG
619 hits | 53.96 KB | Posted: 1/3/08
Photo taken to show that brackets are lined up where the axle pivot bolt goes
windscreen2.JPG
609 hits | 70.6 KB | Posted: 12/10/08
Hit rock at 70+ mph. Little glass shards went all the way back to the parcel shelf under the rear window
IMGA0008.JPG
604 hits | 32.94 KB | Posted: 1/3/08
IMGA0013.JPG
604 hits | 33.39 KB | Posted: 1/3/08
windscreen1.JPG
584 hits | 84.94 KB | Posted: 12/10/08
Rock flicked up by car in front. 70+ mph
IMGA0007.JPG
579 hits | 28.37 KB | Posted: 1/3/08
Bad night time shot.
The bracket is not big enough. A bolt cannot go through the holes in the bracket, and the axle pivot bushing.
Maintenance & Modification Logs
This user hasn't added any log entries, yet.
