1990 Ford Bronco
| Owner: |
highcetane (All of this user's registries on SuperMotors) |
| From: |
Dorothy, NJ, U.S.A. (Other registries in NJ) |
| Year, Make, & Model: |
1990 Ford Bronco (Other Ford Broncos) |
| Avatar: |
 |
| Nickname: |
Blue Bronco |
| Mileage: |
95000 |
| Engine: |
351w, GT40 heads, Crane Cam, Shorty headers, Magnaflow Y single Cat, Summit 3" Turbo muffler, 3'' all the way.
Complete rering & bearing 3/09 |
| Drivetrain: |
Stock E4OD, Factory posi w/355's, Rancho 2" Leveling coils, ProComp Long AAL's, 32" BFG MT's, |
| Notes: |
Bought from orig owner, nice interior, ice cold R12 air. Truck is now semi retired to occasional trail rides with my daughter, and standard equipment is fishing poles for the lake down the street.
Future plans to install snow plow, upgrade to 3G alternator, improve trans performance & durability.
The Hammered paint on the frame made a nice improvement, and my attention on the wheel wells next Spring will fix the rust once & for all. Then i will most likely paint the entire truck Dk blue.
I have a newer style front clip that is in perfect condition, cant decide if I will change it over. |
| Last Updated: |
1/3/2010 |
| Hits: |
2482 |
| Folder |
 |
 |
 |
Hits |
 |
Created |
Updated |
 Bronco | 34 | 0 | 0 | 11,915 | 0 | 8/16/09 | 1/3/10 |
 007.JPG
398 hits | 55.59 KB | Posted: 1/3/10
 006.JPG
399 hits | 40.88 KB | Posted: 1/3/10
Side by side after. Did I gain anything?...I'll never know, but I sure didnt lose anything.
 005.JPG
472 hits | 41.86 KB | Posted: 1/3/10
Side by side before
 004.JPG
370 hits | 69.62 KB | Posted: 1/3/10
Stock manifold..measures 2 3/8" I am not going to do this work and worry at night of the possibility of less flow.
 002.JPG
388 hits | 56.68 KB | Posted: 1/3/10
D Side Summit (Pacesetter) Shorty Header. Out of the box the outlet only measures 1 13/16".
 005.JPG
421 hits | 83.75 KB | Posted: 1/3/10
 004.JPG
416 hits | 71.56 KB | Posted: 1/3/10
New Zone water pump.....Lifetime warranty- I got that going for me.
 003.JPG
479 hits | 81.02 KB | Posted: 1/3/10
GT40 heads, a gift from work. 2 times through a parts washer & most of the black paint stayed on..pretty good stuff. They were low hour Marine heads, but had been sitting in my shed for 5 years.
 002.JPG
382 hits | 84.18 KB | Posted: 1/3/10
New Timing Chain. Ford could have given me better gaskets & let the mech fuel pump eccentric off.
 003.JPG
633 hits | 74.15 KB | Posted: 11/9/09
Better shot of the rollpan....I tweaked the tailpipe with a slight up angle to go with the taper of the roll pan....may put it back to level...we'll see.
003.JPG
479 hits | 81.02 KB | Posted: 1/3/10
GT40 heads, a gift from work. 2 times through a parts washer & most of the black paint stayed on..pretty good stuff. They were low hour Marine heads, but had been sitting in my shed for 5 years.
005.JPG
472 hits | 41.86 KB | Posted: 1/3/10
Side by side before
 001.JPG
436 hits | 78.75 KB | Posted: 1/3/10
Back from friend's HD parts washing machine. New cam bearings, hone'd, new Clevite 77 rings & TRW bearings. Everything measured up within std...
Brass freeze plugs, new oil pump, and yes, I use a gasket between the pump & block...you should too.
005.JPG
421 hits | 83.75 KB | Posted: 1/3/10
004.JPG
416 hits | 71.56 KB | Posted: 1/3/10
New Zone water pump.....Lifetime warranty- I got that going for me.
 008.JPG
415 hits | 80.54 KB | Posted: 1/3/10
Suprisingly clean for 92 k..no sludge whatsoever.....
 003.JPG
412 hits | 82.87 KB | Posted: 1/3/10
Oil stain from Intake Manifold leak
 Bronco Pic IMG_1162.JPG
409 hits | 90.88 KB | Posted: 8/16/09
Maintenance & Modification Logs
This user hasn't added any log entries, yet.
|
|
