IMG_0602.JPG
830 hits | 62.78 KB | Posted: 4/5/14

IMG_0603.JPG
258 hits | 63.46 KB | Posted: 4/5/14

IMG_0604.JPG
268 hits | 59.09 KB | Posted: 4/5/14

IMG_0605.JPG
251 hits | 63.92 KB | Posted: 4/5/14

IMG_0606.JPG
274 hits | 66.4 KB | Posted: 4/5/14

IMG_0607.JPG
362 hits | 70.5 KB | Posted: 4/5/14

IMG_0608.JPG
307 hits | 56.76 KB | Posted: 4/5/14

IMG_0609.JPG
372 hits | 69.61 KB | Posted: 4/5/14

IMG_0610.JPG
303 hits | 70.17 KB | Posted: 4/5/14

IMG_0611.JPG
335 hits | 66.26 KB | Posted: 4/5/14

IMG_0621.JPG
326 hits | 72.63 KB | Posted: 4/5/14

IMG_0625.JPG
328 hits | 67.84 KB | Posted: 4/5/14

IMG_0626.JPG
330 hits | 63.95 KB | Posted: 4/5/14
Going to chop this frame. Custom café/street fighter all the way. Tank will be custom too.

IMG_0695.JPG
252 hits | 65.5 KB | Posted: 6/8/14
Decided to replace the cylinder head gasket anyway, very dirty in there. Going to clean it up.

IMG_0696.JPG
278 hits | 67.65 KB | Posted: 6/8/14
Valve cover gasket was leaking pretty bad. Replacing all gaskets for a fresh start.

Frame1.jpg
247 hits | 58 KB | Posted: 7/6/14

frame2.jpg
207 hits | 43.49 KB | Posted: 7/6/14
Close it all in with whatever welding ability you have or prefer. I only had my MIG with flux core a...

frame3.jpg
244 hits | 57.6 KB | Posted: 7/6/14
Careful measuring and lots of eyeballing to get the other side the same dimensions. However, there i...

concourse.jpg
240 hits | 53.06 KB | Posted: 7/6/14
This little gun is awesome for small projects. Great control, excellent spray. Never an issue. Eastw...

engine.jpg
247 hits | 60.31 KB | Posted: 7/6/14
Nasty and unhappy.

engine2.jpg
241 hits | 57.5 KB | Posted: 7/6/14
Clean and happy!

framestart.jpg
242 hits | 62.86 KB | Posted: 7/6/14
Big things have small beginnings.

framestart2.jpg
241 hits | 60.61 KB | Posted: 7/6/14
And now for the ribs.

swingarm.jpg
256 hits | 37.44 KB | Posted: 7/6/14
Black it out...

wheel.jpg
234 hits | 54.01 KB | Posted: 7/6/14
Shiny!

leftsideframe.jpg
243 hits | 70.21 KB | Posted: 7/7/14
I added an extra half inch tube to the top of the cage to fill in the gap a little more. It snugs th...

Rightsideframe.jpg
236 hits | 70.92 KB | Posted: 7/7/14
The right side is the same as the left without the fuel access.

tankon.jpg
233 hits | 70.53 KB | Posted: 7/7/14
With the tank on for the final fit. I cut the rear as well and ran all tubes so they flow the same l...

tail.jpg
259 hits | 57.32 KB | Posted: 7/14/14
Add the rod to shape the tail.

tail2.jpg
241 hits | 57.71 KB | Posted: 7/14/14
I will cut and shape the lower tail frame so it smooths out better, then sheet metal it in and begin...

Tail3.jpg
241 hits | 63.54 KB | Posted: 7/15/14
Sheet metal for the tail.

tail4.jpg
257 hits | 59.39 KB | Posted: 7/15/14
From the rear.

tail5.jpg
278 hits | 47.95 KB | Posted: 7/15/14
Sheet metal tacked in from the side. Still have some shaping and paint prep.

CompletFrameFab.jpg
285 hits | 54.55 KB | Posted: 7/18/14
Metal work is done. A good washing before paint prep.

CompletFrameFab2.jpg
254 hits | 65.22 KB | Posted: 7/18/14
The tail fits the seat very well. After a little filler to smooth out the sharp edges, it will flow ...

CompletFrameFab3.jpg
203 hits | 62.05 KB | Posted: 7/18/14
Getting the rear to curve was a little tricky, but the end result was where it needed to be to maint...

Rebar.jpg
223 hits | 66.35 KB | Posted: 7/18/14
Did not have the right size round bar laying around, but I did have some rebar that was just right! ...

994134_10202191130684449_5082732725043633457_n.jpg
224 hits | 41.93 KB | Posted: 7/20/14
Working the filler is a long process and the sanding is labor intensive. But it is looking as planne...

IMG_0185.JPG
221 hits | 64.53 KB | Posted: 8/29/14
Finally got paint and clear on the frame after all the body work and endless sanding. Happy with the...

IMG_0192.JPG
238 hits | 64.4 KB | Posted: 8/29/14
Stripped the tank bare and put a fresh three coats of BLVD Black on, followed by three coats of clea...

IMG_0193.JPG
268 hits | 82.19 KB | Posted: 8/29/14
Added two extra coats of clear to the wheels. They look a lot better.

dryfitting1.jpg
264 hits | 63.72 KB | Posted: 10/11/14
Lining up the forks.

dryfitting2.jpg
250 hits | 69.97 KB | Posted: 10/11/14
Ready for rubber.

dryfitting3.jpg
303 hits | 65.52 KB | Posted: 10/11/14
Rubber and brakes are on the bike.

dryfitting4.jpg
283 hits | 61.79 KB | Posted: 10/11/14
Superbike bars are on and I really like the look.

dryfitting5.jpg
314 hits | 56.07 KB | Posted: 10/11/14
Getting closer.

dryfitting6.jpg
318 hits | 57.5 KB | Posted: 10/11/14
The gold hand controls are amazing in contrast to the black skin.

tailLEDs.jpg
323 hits | 49.79 KB | Posted: 10/11/14
Simple tail section.

vapordash.jpg
308 hits | 79.95 KB | Posted: 10/11/14
Simple dash to match to the tail.

brakes.jpg
295 hits | 76.18 KB | Posted: 10/17/14
I relocated the rear brake reservoir to be under the front seat bracket.

Buttoned1.jpg
309 hits | 62.01 KB | Posted: 10/17/14
Just need to install the shorty exhaust.

buttoned2.jpg
344 hits | 69.37 KB | Posted: 10/17/14
Pleased with the look.