Steve83 > 1983 Ford Bronco > open folder 97-03-10 Frame Noise

TSB 97-03-10 Frame Noise Publication Date: FEBRUARY 3, 1997 IF THE IMAGE IS TOO SMALL, click it. ...
Hits: 4933
Size: 26.62 KB
Posted: 12/21/06
TSB 97-03-10 Frame Noise Publication Date: FEBRUARY 3, 1997 IF THE IMAGE IS TOO SMALL, click it. ...		3. INSPECT FRAME BOLTS FOR PROPER INSTALLATION TORQUE Inspect and tighten all front end component...
Hits: 2945
Size: 12 KB
Posted: 12/21/06
3. INSPECT FRAME BOLTS FOR PROPER INSTALLATION TORQUE Inspect and tighten all front end component...		Knock the rivet pin out of the blind side with a 6.35mm (1/4") drift punch and hammer (Figure 2...
Hits: 2403
Size: 11.36 KB
Posted: 12/21/06
Knock the rivet pin out of the blind side with a 6.35mm (1/4") drift punch and hammer (Figure 2...		> Cut the rivet's head off with a hammer and flat chisel (Figure 3). Click "Next" besi...
Hits: 2342
Size: 11.01 KB
Posted: 12/21/06
> Cut the rivet's head off with a hammer and flat chisel (Figure 3). Click "Next" besi...		> Knock the sleeve out of the blind side with a 9.525mm (3/8") drift punch and hammer (Figure ...
Hits: 2361
Size: 10.02 KB
Posted: 12/21/06
> Knock the sleeve out of the blind side with a 9.525mm (3/8") drift punch and hammer (Figure ...
2. After removing the rivet, verify the noise came from this location by pounding a wedge between th...
Hits: 3142
Size: 41.32 KB
Posted: 12/21/06
2. After removing the rivet, verify the noise came from this location by pounding a wedge between th...		IF THE IMAGE IS TOO SMALL, click it. 5. Install a 9/16" Grade 8 torque prevailing Nut (34990-S...
Hits: 2775
Size: 42.73 KB
Posted: 12/21/06
IF THE IMAGE IS TOO SMALL, click it. 5. Install a 9/16" Grade 8 torque prevailing Nut (34990-S...		a. Slide the bolt and washer into the "window" opening on the outside of the frame siderai...
Hits: 3194
Size: 29.33 KB
Posted: 12/21/06
a. Slide the bolt and washer into the "window" opening on the outside of the frame siderai...		a. Torque all three (3) bolts/nuts at the crossmember-to-frame siderail at the wraparound side (Figu...
Hits: 2441
Size: 30.35 KB
Posted: 12/21/06
a. Torque all three (3) bolts/nuts at the crossmember-to-frame siderail at the wraparound side (Figu...		a. Torque the gusset-to-frame bolts (Figure 8, Number 1). b. Torque the crossmember-to-frame bolt...
Hits: 2600
Size: 24.66 KB
Posted: 12/21/06
a. Torque the gusset-to-frame bolts (Figure 8, Number 1). b. Torque the crossmember-to-frame bolt...
Warranty LABOR ALLOWANCE Click "Next" beside the image above to continue.
Hits: 2235
Size: 82.21 KB
Posted: 12/21/06
Warranty LABOR ALLOWANCE Click "Next" beside the image above to continue.		DEALER CODING OASIS CODES: 305000, 390000, 702000, 702100 If viewing a single image per page, c...
Hits: 2240
Size: 24.18 KB
Posted: 12/21/06
DEALER CODING OASIS CODES: 305000, 390000, 702000, 702100 If viewing a single image per page, c...		Factory welds in a '93 Bronco #1 (engine) crossmember LHR.
Hits: 1993
Size: 95.18 KB
Posted: 5/6/12
Factory welds in a '93 Bronco #1 (engine) crossmember LHR.		Factory welds in a '93 Bronco #1 (engine) crossmember RHF.
Hits: 1716
Size: 88.94 KB
Posted: 5/6/12
Factory welds in a '93 Bronco #1 (engine) crossmember RHF.		Factory welds in a '93 Bronco #1 (engine) crossmember RHR.
Hits: 1847
Size: 97 KB
Posted: 5/6/12
Factory welds in a '93 Bronco #1 (engine) crossmember RHR.
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2024 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog