File 399 of 468
Prev | Next

bumperf92.jpg | Hits: 10268 | Posted on: 6/23/08 | View original size (234.87 KB)

'92-97 Front Bumpers
IF THE IMAGE IS TOO SMALL, click it.
ERRORS: in the center inset (Section B) 3 should be 9 and 4 should be 8 as in Section A; in the main view right 9 should not be a single strip - it should be 2 outboard strips and a separate center nostril trim


1 Front Bumper 17757 (chrome solid F2TZ17757A interchange FO1002236; chrome rub F2TZ17757B interchange FO1002237; chrome vented F3TZ17757AB interchange FO1002254; black rub interchange FO1002239; black solid F2TZ17757D interchange FO1002340)
2 Nut (4 Req'd) N804525-S59 (21mm drive)
3 Frame (Side Rail Tab) 5005
4 Bumper Isolator and Bracket Spacer 17765 (RARELY used)
5 Rivet (12 Req'd) 388442-S309 (1/4" all-steel galvanized/cadmium)
6 Front License Plate Mounting Bracket F2TZ17A385A (Interchange Part Number: FO1068101)
7 Rivet (3 Req'd) N803043-S (1/4" all-steel black)
8 Front Valance Panel F2TZ17626A (FO1095154)
9 Front Bumper Horizontal Pad w/o turbo F2TZ17K833A (FO1057220)
10 Arm, Front Bumper 17766 (RH F2TZ-17752-A, FO1066108 ); 17767 (LH F2TZ-17752-B, FO1067108 ); aftermarket pair
11 Screw and Washer N606689-S301 (10mm drive)
12 U-Nut N800296-S301 (8mmx1.25))
13 Reinforcement, Front Bumper, Bronco Only F2TZ17A792A (RH, FO1067110); F2TZ17A792B (LH, FO1066110)
14 Bolt Assembly (2 Req'd) N605934-S53
A - Tighten to 60-80 N-m (44-59 Lb-Ft)
B - Tighten to 19-25 N-m (14-18 Lb-Ft)

Standard Bumper ('92-97)
Bare chrome (no trim holes) F2TZ17757A (aftermarket FO1002236)
Set of bumper, trim, chin valance, & mounts (aftermarket) (no fasteners)

Turbo Diesel Bumper ('94-97)
Left side trim F3TZ17K833J interchange FO1058271
Right side trim F3TZ17K833H interchange FO1059271
Pair of outboard trims (aftermarket) FO1059271 & FO105827
Nostril trim F3TZ17K833K interchange FO1057272
Set of 3 trims (aftermarket) FO1059271, FO105827, & FO1057272
Set of bumper, trim, & mounts (aftermarket) (no chin valance or fasteners)

Removal
1. Support the bumper assembly and remove the four nuts (two each side) attaching the assembly to the frame mounting brackets.
2. Carefully lower the bumper assembly from vehicle and lay it on a protective surface.
3. If replacing bumper bar, remove front bumper horizontal pads (17C829) by pinching rear pegs & pushing them through, front fender apron and radiator support braces (16A023) or front license plate mounting bracket (17A386) by drilling out rivets.
4. Sight along the frame tabs, and bend them into alignment using a large adjustable wrench.

.

Installation
1. If bumper bar was replaced, install front bumper horizontal pads, front fender apron and radiator support braces or front license plate mounting bracket.
2. Align bumper assembly mounting studs to the holes in the frame mounting brackets.
3. Insert studs through slot in frame brackets. Loosely assemble nuts to hold front bumper (17757) to frame (5005) (side rail).
4. Align front bumper to front fenders (16005) and sheet metal stone deflector maintaining a parallel margin of 18-31mm (.76-1.24 inch). If rotation is an issue, use shim as required.
5. After front bumper is aligned, tighten nuts to 60-80 N-m (44-59 lb-ft) per TSB 95-07-07.

See also:
. . . .